OWATROL-GLV

gb-owatrol-glv

Anti-corrosive galva look

OWATROL-GLV is a highly flexible, anti-corrosive coating that possesses the deep penetrating and adhesion properties of MARINE OIL. OWATROL-GLV will restore rusted and corroded surfaces above the waterline to give lasting protection and greatly prolong the life of the treated surface. OWATROL-GLV has excellent abrasion resistance, withstands chemical attack and is ideal in aggressive climatic conditions where a high resistant finish is necessary. 

Properties

  • Excellent resistance against the effects of the weather.
  • Safe to use in confined areas - Does not emit any dangerous fumes.
  • Withstand temperatures up to 175°C (347°F) once cured.
  • Excellent light and heat reflecting properties.
  • Expels moisture and air from rusted surfaces – Stops and stabilises rust without chemical reaction. 
  • MARINE OIL* based (OWATROL OIL*).
  • Easy application.
  • Highly elastic - Will not crack, peel or blister. 

Where to use

  • Interior and exterior.
  • Horizontal and vertical surfaces.
  • Ferrous and non-ferrous metals - Aluminium, Copper, Steel, Iron, Galvanised…
  • Wood, Painted and varnished surfaces…
  • Deck fixings, Balconies, Trailers, Pipes, Pumps…
  • Non-marine - Grills, Machinery, Tanks, Exhausts…

Preparation surface

  • Surfaces must be clean, dry and free of oil, grease, grime and other surface contamination.
  • Remove all loose and flaking rust and old paint back to a sound surface and edge.
  • Feather in any sharp edges.
  • Clean surfaces thoroughly using a suitable non-oxidising solvent e.g. Acetone, White-Spirit…

Application

  • Stir can well before and during use. Do not thin.

New Surfaces exc’ Aluminium Surfaces

  • Abrade surfaces with 60-120 grit paper. Fibreglass 180-220 grit paper.
  • For inaccessible areas use a liquid sander e.g. diluted OWAYELL (Consult us). Rinse thoroughly and allow to dry.
  • Prime new metal and galvanised surfaces with 1 coat of MARINE OIL or OWATROL-C.I.P. and allow to dry 24 hours.
  • Apply 1 or 2 coats of OWATROL-GLV.
  • For new metal surfaces subject to aggressive climatic conditions apply 2 coats.

New Aluminium Surfaces

  • Abrade surfaces with 60-120 grit paper compatible with Aluminium or Sandblast.
  • For inaccessible areas use a liquid sander e.g. diluted OWAYELL (Consult us). Rinse thoroughly and allow to dry.
  • Apply 1 or 2 coats of OWATROL-GLV allowing drying time between coats.

Clean, Lightly Rusted Metal

  • Apply 2 coats of OWATROL-GLV allowing drying time between coats.

Old Severely Rusted Surfaces

  • Apply wet on wet applications of MARINE OIL until rust is fully saturated and allow to dry. Saturation is indicated by a uniform glossy appearance to the surface when MARINE OIL is dry.
  • Apply 2 coats of OWATROL-GLV allowing drying time between coats.

Previously Coated Surfaces

  • Spot prime all exposed metal with MARINE OIL or OWATROL-C.I.P. depending on severity of rust and allow to dry. 
  • Apply OWATROL-GLV to primed areas to bring level with existing finish, allowing drying time between coats.
  • Apply 1 or 2 coats of OWATROL-GLV over entire area; allowing drying time between coats. 

Clean-up

  • Clean all tools and equipment with white sprits while still wet. If allowed to dry, remove with paint stripper.
  • NOTE: Any rags, soaked in OWATROL®-GLV may spontaneously catch fire if improperly discarded. Rags must be saturated with water after use or placed in a sealed, water filled metal container alternatively they can be left out flat to dry before disposing of. 

Caution

  • Do not apply OWATROL®-GLV direct to new metal (except aluminium), alloys inc’ steel and galvanised surfaces as Galvanic corrosion caused through contact with moisture and air can occur.

Information

Coverage: 18 m2 (193 ft2) per litre. Actual coverage will vary depending on application method, type, texture, age and porosity of the surface.
Application tools: Brush. Roller. Airless Sprayer (0.4 mm x 80° @ 1860-2000 psi (128-138 bars)). 
Application temperature: between 5°C (41°F) and 35°C (95°F).
Re-coating time: 8-24 hours.

Container size

0.5 LITER (for larger sizes contact us).  

Watch the product video