DEKS OLJE D.2

gb-deksoljed2

Fender cleaner & black mark remover

DEKS OLJE D.2 is a varnish like, tough, flexible and durable finish that enhances the natural beauty of the wood. Easy to maintain and apply the more coats of DEKS OLJE D.2 applied the higher the gloss finish. Unlike traditional varnishes DEKS OLJE D.2 will not craze or blister and because of DEKS OLJE D.1's penetrating qualities will not peel or flake as water is unable to get in to the wood.

Properties

  • Flexible film that does not craze, peel or flake.
  • High gloss finish.
  • Highly transparent varnish - enhances the natural beauty of the wood.
  • Long term protection.
  • No sanding between coats.
  • Easy maintenance.
  • Easy repair, no stripping.

Where to use

  • Hardwoods and Exotic hardwoods - Oak, Chestnut, Ash, Teak, Ipe, Mahogany, Bangkirai...
  • Softwoods - Pine, Spruce, Larch...
  • New or weathered wood.
  • Exterior - Garden furniture, window and door frames, gates...
  • Interior - Panelling, doors, windows, joinery...
  • Marine - All applications above the waterline (Handrails, Wheel houses, trim...).
  • Horizontal & vertical surfaces.

Preparation surface

General Directions:

  • Surfaces must be clean, dry and free of dirt, grease, grime and mildew.
  • Treat mildew with a 50/50 bleach/water solution. Scrub solution on to the surface and allow to stand for 10-15 minutes; rinse thoroughly.
  • DEKS OLJE D.2 may only be applied to surfaces previously finished with DEKS OLJE D.2 or DEKS OLJE D.1.
  • All other finishes must be completely and thoroughly removed.

New wood:

  • All new wood must be treated with DEKS OLJE D.1.

Weathered wood surfaces (untreated):

  • Refer to the Technical Data Sheet for DEKS OLJE D.1

Previously oiled and coated surfaces (Paint, Stain, Varnish....):

  • Refer to the Technical Data Sheet for DEKS OLJE D.1

Weathered wood previously treated with DEKS OLJE D.1:

  • Clean with DECK CLEANER and restore DEKS OLJE D.1 before applying DEKS OLJE D.2.

Wood already treated with DEKS OLJE D.2:

  • See technical data sheet.

Application

  • DO NOT THIN. USE AS IS.
  • Apply 6 coats of DEKS OLJE D.2 allowing a minimum of 12 hours between coats.
  • All coats should be applied within 1 month.
  • Sanding between coats is not required.
  • For an extra high gloss finish, sand between the last 2 coats with 600 grit paper.
  • Allow 3 days for DEKS OLJE D.2 to set-up and dry, before putting the boat in service.

Clean-up

  • Clean all tools and equipment with white spirits while still wet. If allowed to dry, remove with paint stripper.

To maintain product

  • Wash frequently with fresh water to remove salt and dirt.

Areas worn back to DEKS OLJE D.1 treated wood:

  • Clean worn area with DECK CLEANER. Leave to dry.
  • Sand with 320 grit paper.
  • Top up DEKS OLJE D.1.
  • Apply required number of DEKS OLJE D.2 coats to bring up to level of existing finish.

Rough or abraded areas:

  • Wet sand surface using 320 grit paper and DEKS OLJE D.1 as the lubricant.
  • Wipe over with a clean, dry, lint free cloth to remove DEKS OLJE D.1 and sanding residue. Leave to dry 24 hours.
  • Apply 2 coats (minimum) or more of DEKS OLJE D.2, blending in to areas with good finish.

New full coat:

  • Wet sand the whole surface using 320 grit paper and DEKS OLJE D.1 as the lubricant.
  • Wipe over with a clean, dry, lint free cloth to remove DEKS OLJE D.1 and sanding residue. Leave to dry 24 hours.
  • Apply 1 or 2 coats of DEKS OLJE D.2 as desired.

Caution

  • DEKS OLJE D.2 should only be applied to surfaces treated with DEKS OLJE D.1 or previously finished with DEKS OLJE D.2.
  • Do not apply DEKS OLJE D.2 in wet weather or late in the day when dew or fog may be expected.
  • This may dull a newly set film causing it to blush - exposure to sunlight usually removes the discoloration.
  • DEKS OLJE D.2 is very slippery, especially when wet and we therefore do not recommend the use of it on decks and other areas where it will be walked on.

Information

  • Coverage: 15 m² per litre
  • Application tools: Brush, Roller
  • Application temperature: between 8°C and 35°C
  • Dry time: 12-24 hours per coat

Container size

  • 1 LITER (1.06 U.S QUART)
  • 2.5 LITERS (0.66 U.S. GALLON)
  • 10 LITERS (2.64 U.S. GALLON)